Effects of Colloidal Nanosilica on Epoxy-based Nanocomposite Coatings

Document Type : Original Article

Authors

1 Section of Chemical Engineering Technology, University of Kuala Lumpur, Alor Gajah, Melaka, Malaysia

2 Faculty of Chemical and Natural Resources Engineering, Universiti Malaysia Pahang, Gambang, Malaysia.

3 Malaysia France Institute, Universiti of Kuala Lumpur, Bangi, Malaysia.

Abstract

Epoxy-based nanocomposites were fabricated with different content of colloidal silica nanoparticles such as 10.0, 20.0 and 30.0 wt %, through solution casting. The covalent bonding interfaces, resulting from a ring-opening reaction between silica nanoparticles and epoxy matrix were confirmed by the Fourier transform (FT-IR) infrared spectroscopy. These nanocomposites were characterized for thermal stability, glass transition temperature and adhesive properties using thermogravimetric analyzer (TGA), differential scanning calorimeter (DSC) and cross-cut tape test. In addition, chemical resistance was assessed by immersing the films in different chemical solution (acid, alkali and salt solution) for 21 days. It was found that the properties of the nanocomposites were increased proportionally to the content of silica nanoparticles up to a certain amount of loading. After that the properties were decreased. The surface morphology of the nanocomposites was observed by scanning electron microscopy (SEM), which showed that the silica nanoparticles distributed uniformly. In addition, the nanocomposites were studied on UV radiation absorption by UV-Vis spectrophotometer. Excellent UV radiation was noticed by the nanocomposite films. The oxygen transmission rate (OTR) and water contact angle (WCA) testing of the nanocomposite films was also impressive.

Keywords


  1. T. Wan, J. Lin, X. Li, W. Xiao, Preparation of epoxy-silica-acrylate hybrid coatings, Polym. Bull., 59(2008), 749-758.
  2. H. Behniafar, M. K. Nazemi, Effect of amine-functionalized silica nanoparticles on thermal and mechanical behaviors of DGEBA/IPD epoxy networks, Polym. Bull., 74(2017), 3739–3749.
  3. M. R. Islam, M. D. H. Beg, S. S. Jamari, Dispersion of montmorillonite nanoclays and their effects on the thermomechanical, structural and drying properties of palm oil based coating, Prog. Org. Coat., 91(2016), 17-24.
  4. M. R. Islam, A. N. Yahaya, N. Isa, Effects of zinc oxide on pretreated multiwalled‐carbon‐nanotube‐reinforced biobased polyesters, J. Appl. Polym. Sci., 134(2017), 44627.
  5. T. Nazir, A. Afzal, H. M. Siddiqi, S. Saeed, M. Dumon, The influence of temperature and interface strength on the microstructure and performance of sol–gel silica–epoxy nanocomposites, Polym. Bull., 67(2011), 1539-1544.
  6. M. R. Islam, M. D. H. Beg, S. Shima, The effect of five different types of acid anhydrides and incorporation of montmorillonite nanoclays on thermosetting resins, Polym. Bull., 15(2015), 1-24.
  7. M. R. Islam, M. D. H. Beg, S. Shima, Characterization of multi wall carbon nanotubes filled palm oil based polyalkyds: effects of loading and in situ reaction, J. Appl. Polym. Sci., 133(2016), 42934.
  8. F. Branda, F. Tescione, V. Ambrogi, D. Sannino, B. Silvestri, G. Luciani, A. Costantini, A new extra situ sol–gel route to silica/epoxy (DGEBA) nanocomposite. A DTA study of imidazole cure kinetic, Polym. Bull., 66(2011), 1289-1300.
  9. J. W. Gang, H. J. Ming, L. Liang, Z. J. Qing, C. C. Nan, Improving the corrosion performance of epoxy coatings by chemical modification with silane monomers, Surf. Coat. Technol., 201(2007), 4789-4795. 
  10. J. L. V. Caselis, R. A. Serrano, E. R. Rosas, Preparation and characterization of epoxy-silica coatings using rhodamine 6G as dye, Mater. Res. Soc. Proc., 1613(2014), 45-51.
  11. H. J. Hyuk, L. J. Woong, L. Byoungsang, C. H. Hun, L. Byungkwon, L. J. Heon, Chemical effects of organo-silanized SiO2 nanofillers on epoxy adhesives, J. Indus. Eng. Chem. 5(2017), 1-6.
  12. G. Prashant, B. Madhu, Development of siliconized epoxy resins and their application as anticorrosive coatings, Adv. Che. Eng. Sci., 1(2011), 133-139.
  13. Q. Min, M. S. Andrew, H. T. Xiu, T. Z. Xian, L. W. Sudesh, Two-part epoxy-siloxane hybrid corrosion protective coatings for carbon steel, Thin Solid Film, 517(2009), 5237-5242.
  14. A. Allahverdi, E. Morteza, J. Hadi, A. Shervin, The effect of nanosilica on mechanical, thermal and morphological properties of epoxy coating, Prog. Org. Coat., 75(2012), 543-548.
  15. M. Paraimala, M. R. Islam, R. M. Yunus, Effects of nano- and micro-sized inorganic filers on the performance of epoxy hybrid nanocoatings, Polym. Polym. Compos., 27(2019), 82-91.
  16. M. Paraimala, M. R. Islam, R. M. Yunus, Effects of nanosilica, zinc oxide, titatinum oxide on the performance of epoxy hybrid nanocoating in presence of rubber latex, Polym. Test., 70(2018), 197-207.
  17. S. Xianming, A. N. Tuan, S. Zhiyong, L. Yajun, A. Recep, Effect of nanoparticles on the anticorrosion and mechanical properties of epoxy coating, Surf. Coat. Technol., 204(2009), 237-245.
  18. Derya, N. K. Apohan, G. Atilla, Preparation and characterization of UV-curable epoxy-silica nanocomposite coatings, Prog. Org. Coat., 65(2009), 477-483.
  19. Z. Xiaohua, X. Weijian, X. Xinnian, Z. Zhenghun, Y. Rangi, Toughening of cycloaliphatic epoxy resin by nanosize silicon dioxide, Mater. Lett., 60(2006), 3319-3323.
  20. S. R.Tijana, V. D. Jasna, B. J. Katarina, N. G. Branimir, S. M. Dejan, G. P. Ivanka, S. D. Enis, Important of epoxy resin properties by incorporation of TiO2 nanoparticles surface modified with gallic acid esters, J. Mater. Design., 62(2014), 158-167.
  21. V. Mittal, Effect of the presence of excess ammonium ions on the clay surface on permeation properties of epoxy nanocomposites, J. Mater. Sci., 43(2008), 4972-4978.
  22. T. N. Chen, D. S. Wuu, C. C. Wu, C. C. Chiang, H. B. Lin, Y. P Cheri, R. H. Horng, Effect of plasma pretreatment on silicon nitride barrier films on polycarbonate substrate, Solid Films., 514(2006), 188-192.
  23. N. I. Kim, H. M. Kang, T. H. Yoon, Study of heat of reaction between plasma-polymer-coated silica fillers and biphenyl epoxy resin, J. Adhes. Sci. Technol., 18(2004), 1325-1338.
  24. A. Sharif, A. P. Gupta, S. Eram, A. Manawwer, S. K. Pandey, Synthesis, characterization and development of high performance siloxane-modified epoxy paints, Prog. Org. Coat., 54(2005), 248-255.
  25. C. E. C. Arola, S. Raffaella, F. Mariaenrica, Microgel modified UV-cured methacrylic-silica hybrid: Synthesis and characterization, Mater., 32(2013), 3805-3825.
  26. B. Ehsan, J. Ali, R. Zhara, S. Sarah, S. M. Razep, Anti-corrosion hybrid coatings based on epoxy-silica nano-composites: Toward relationship between the morphology and EIS data, Prog. Org. Coat., 77(2014), 1169-1183.
  27. W. C. Chang, H. S. L. Chung, Preparation of epoxy/silica and epoxy/titania hybrid resists via a sol-gel process for nanoimprint lithography, J. Physc. Chem. C., 114(2010), 2179-2183.
  28. S. S. Pathak, A. Sharma, A. S. Khanna, Value addition to waterbone polyurethane resin by silicone modification for developing high performance coating on aluminium alloy, Prog. Org. Coat., 65(2009), 206-216.
  29. R. Galina, L. Marianne, O. Eriksen, O. Gregersen, Surface chemical modification of microfibrillated cellulose: improvement of barrier properties for packaging application, Cellulos., 18(2011), 127-134.
  30. Sungtack, I. H. Sung, R. C. Chul, P. Min, R. Soonho, K. Junkyung, Preparation and characterization of epoxy composites filled with functionalized nanosilica particles obtained via sol-gel process, Polymer, 42(2001), 879-887.
  31. B. Ramezanzadeh, M. M. Attar, Characterization of the fracture behavior and viscoelastic properties of epoxy-polyamide coating reinforced with nanometer and micrometer sized ZnO particles, Prog. Org. Coat., 71(2011), 242-249.
  32. T. Erjun, B. Feng, K. Andrew, E. Mohamed, L. Shaojie, Y. Miao, Z. Dishun, Fabrication of an epoxy graft poly(St-acrylate) composite latex and its functional properties as a steel coating, Prog. Org. Coat, 77(2014), 1854-1860.
  33. S. Santanu, M. J. Thomas, Influence of filler loading on dielectric properties of epoxy-ZnO nano-composites, IEEE Transac. Elec. Insul., 6(2009), 531-542.
  34. C. Chao, T. Yongjun, S. Y. Yun, X. Zhigang, X. Yang, X. Xiaolin, M. Y. Wing, High-performance epoxy/silica coated silver nanowire composites as underfill material for electronic packaging, Compos. Sci. Technol., 105(2014), 80-85.
  35. T. H. Hsieh, A. J. Kinloch, K. Masania, J. S. Lee, A. C. Taylor, S. Sprenger, The toughness of epoxy polymers and fibre composites modified with rubber microparticles and silica nanoparticles, J. Mater. Sci., 45(2010), 1193-1210.