Characterizing films of polyethylene blends: An application of colorimetric parameters measurements


Journal: Vol.8, No.3, Summer 2015 - Article 5   Pages :  219 Until 235



Article Code:
PCCC-2015-02-02-283

Authors:
Mohsen Mohammadi: Qom University of Technology - Department of Polymer Engineering
A. A. Yousefi: Iran Polymer and Petrochemical Institute - Department of Plastics
M. Ehsani: Iran Polymer and Petrochemical Institute - Department of Polymer processing


Article's abstract:

This study reports an application of instrumental color measurement for quantifying and comparing the optical properties of high density polyethylene HDPE and low density polyethylene LDPE blend films and the effect of blending ratio and miscibility on these properties. The technique of spectrophotometry in transmission and reflectance modes can be used as a versatile tool to evaluate the colorimetric parameters of polymers. The optical properties of the films indicated likeliness of affecting color spectrum by incorporating low-density PE LDPE into high-density PE HDPE. This is the principal reason for changing colorimetric parameters of the films. CIE colorimetric values in CIELab and CIELCho color scales and associated parameter Color Intensity CI showed that they are practical for comparing the blend films. The most change in the values versus composition was pertained to films of HDPE-rich blends which were verified miscible using thermal analysis. In this paper it was observed that the used measurement technique, through quantitative parameters provided by it, would be useful to reveal the difference in behavior of the HDPE/LDPE blends at miscible compositions from immiscible ones.


Keywords:
optical properties, polyethylene blend, CIELAB color coordinates, spectrophotometry

References:
1. S. Wang, Y. Zhang, W. Ren, Y. Zhang, H. Lin, Morphology, mechanical and optical properties of transparent BR/clay nanocomposites, Polym Test, 24 (2005), 766-774.#2. P. B. Harrison, R. R. J. Maier, J. S. Barton, J. D. C. Jones, S. McCulloch, G. Burnell, Component position measurement through polymer material by broadband absolute distance interferometry, Meas Sci Technol, 16 (2005), 2066-2071.#3. D. R. Zhang, Z. X. Ma and Q. Z. Yang, Design of Modern Rubber Recipes, Chemical Industry Press, Beijing, 1996.#4. H. Wu, J. Fan, Measurement of radiative thermal properties of thin polymer films by FTIR, Polym Test, 27 (2008), 122-128.#5. C. O. Phillips, E. H. Jewell, T. C. Claypole, D. T. Gethin, Development of measurement techniques to characterize the optical properties of transparent films with application in in-mould decoration, Meas Sci Technol, 19 (2008), 025703.#6. S. G. Lee, R. Shamey, D. Hinks, W. Jasper, Development of a comprehensive visual dataset based on a CIE blue color center: assessment of color difference formulae using various statistical methods, Col Res Appl, 36 (2011), 27-41.#7. I. Niskanen, J. Raty, K.-E. Peiponen, Meas Sci Technol, 17 (2006), N87-91.#8. B. Yuangsoi, O. Jintasataporn, N. Areechon, P. Tabthipwon, The pigmenting effect of different carotenoids on fancy carp (Cyprinus carpio), Aquacul. Nutri. 17 (2011), 306-316.#9. L. Simonot, M. Hebert, D. Dupraz, Goniocolorimetry: from measurement to representation in the CIELAB color space, Col Res Appl, 36 (2011), 169-178.#10. S. Ignell, U. Kleist, M. Rigdahl, On the relation between color, gloss and surface texture in injection-molded plastics, Color Res Appl, 34 (2009), 291-298.#11. J. Berberich, K. H. Dee, Y Hayauchi, C. Portner, A New method to determine discoloration kinetics of uncoated white tablets occurring during stability testing-an application of instrumental color measurement in the development pharmaceutics, Int J Pharm, 234 (2002), 55-66.#12. M. Mohammadi, A. A. Yousefi, M. Ehsani, Thermorheological analysis of blend of high- and low-density polyethylenes, J Polym Res, 19 (2012), 9798-9809.#13. K. Nassau, Color for Science, Art and Technology, Elsevier science, Amsterdam, 1998.#14. Noborou O, Robertson AR, Colorimetry: Fundamental and Applications, John Wiley & Sons, West Sussex, 2005.#15. C. A. Fonseca, I. R. Harrison, An investigation of co-crystallization in LDPE/HDPE blends using DSC and TREF, Thermochemica Acta, 313 (1998), 37-41.#16. H. S. Lee, M. M. Den, Blends of linear and branched polyethylene, Polym Eng Sci, 40 (2003), 1132-1142.#17. B. Neway, U. W. Gedde, Influence of the method of mixing on homogeneity and crystallization kinetics of blends of linear and branched polyethylene, J Appl Polym Sci, 94 (2004), 1730-1736.#18. P. S. Sonawane, S. Radhakrishnan, J. A. Bhangale, A. L. Gadhavi, A. Khare, Development of nanofibrous Morphology in LDPE/LLDPE/PP blends an its effect on mechanical properties of blend films, J Appl Polym Sci, 107 (2008), 4005-4012.#19. A. Wlochowicz, Eder M, Distribution of lamella thickness in isothermally crystallized polypropylene and polyethylene by differential scanning calorimetry, Polymer, 25 (1984), 1268-1270.#20. A. Siegman, Y. Nir, Structure-property relationships in blended of linear low- and conventional low-density polyethylene as blown films, Polym Eng Sci, 27 (1987), 1182-1186.#21. I. A. Hussein, Implication of met compatibility/incompatibility on thermal and mechanical properties of metallocene and Ziegler-Natta linear low density polyethylene (LLDPE) blends with high density polyethylene (HDPE): influence of composition distribution and branch content of LLDPE, Polym Int, 53 (2004), 1327-1335.#22. K. Cho, B. H. Lee, K. M. Hwang, H. Lee, S. Choe, Rheological and mechanical properties in polyethylene blends, Polym Eng Sci, 38 (1998), 1969-1975.#23. D. Curto, F. P. La Mantia and D. Acierno, The rheological behavior of HDPE/ LDPE blends. I. End effects and shear viscosity, Rheol Acta, 22 (1983), 197-208.#24. G. N. Mock, Modern Concern of Color and Appearance, Science Publishers, Enfield, 2000.#25. H. Park, T. W. Lee, Y. C. Kim, O. O. Park, J. K. Kim, White polymer light-emitting devices from ternary-polymer blend with concentration gradient, Chem Phys Let, 403 (2005), 293-297.#26. Q. Niu, Y. Xu, J. Jiang, J. Peng, Y. Cao, Efficient polymer white-light-emitting diodes with a single-emission layer of fluorescent polymer blend, J Luminescence, 126 (2007), 531-535.#27. ASTM E313, ASTM Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates. American Society Testing and Materials, 2005.


Article's file
Page view: 2627
Article's download quantity : 23


Article System Login
Introduction

Manager-in-Chief:
Prof. Zahra Ranjbar
Editor-in-Chief:
Dr. Farahnaz Nourmohammadian
Assistant Editor:
Dr. Mozhgan Hosseinnezhad
ISSN:
2008-2134
ISSN (online):
2383-1790
Publisher:
Institute for Color Science and Technology (ICST)

Quick Access
Publications
E-Vote
What is your opinion about the manuscript subscription system of PCCC website?
Excellent
Good
Fair
Poor
Website Statistics
Page view:2,628
Online Visitors:61